INT100: Instrument & Electrical Maintenance - Dual Craft

24-48 Weeks/720 Hours

Process control Technician use N.C.I.T. National Qualify of Instrument Technicians) and N.I.S.T.   (National Institute of Standards Technology) instrument test standards to calibrate, check install and certify all types of process control instruments, computers,    sensors, transmitters,and recorders.  These are used to measure and   control temperature, pressure, flow vacuum conductivity, analytical   measurement, pH, tank volumes, underground tank leakage, and metrology, etc.  Cornerstone of all manufacture and most trades (Waste Water Operator, Precision Instrument Repair Tech, Computer Control - Networking, Industrial  electrical Instrument Maintenance).      Learn to sell and operate       instruments by understanding how to check, clean, repair, calibrate, and certify electronic components.

[_Title]

1st Quarter  50 Modules     Instrument and Electrical Maintenance - Dual Craft Level 1 
1 Introduction to Process Control, Calibration & Certification   Instrument
2 Understanding Application of Electrical-Instrument Test Equipment
3 Basic  Waste Water Operator Instrument Calibration
4 Math, Theory, Symbols and Drawings      CIT trains for Green Jobs
5 Basic Electrical Maintenance, Instrument Repair and Installation
N.C.I.T. Electrical and Instrumentation Qualify Test Preparation and Final Exam
240 HOURS  maximum  in 8 -13 Weeks       50  Modules = DIPLOMA
2nd Quarter  68 Modules    Instrument and Electrical Maintenance - Dual Craft Level 2
1 Introduction to Waste Water Operator Process Control     Waste Water
2 Calibration Metrology Tester Controller Study 
3 Valve Study
4 Theory of pressure, flow, temperature and ph measuring devices
5 Analytical Measurement Study
6 OSHA 29 CFR 1910.120  18 Modules = (40 + 8 + 8 hours) 
N.C.I.T. Electrical and Calibration Metrology Tester Test Preparation and Final Exam
240 HOURS  maximum  in 8 -13 Weeks      68  Modules = DIPLOMA
3rd Quarter  50 Modules    Instrument and Electrical Maintenance - Dual Craft Level 3
1 Theory Computer, PLC  and Analyzers      Calibration Metrology Tester
2 Calibration Metrology Tester
3 Computer Control interface.
4 Analyzers and Electronic Instruments Trouble Shooting
5 Computer, PLC Loop Checks, Calibration & N.C.I.T. Certification
N.C.I.T.   Computer, PLC Loop Checks Instrument Qualify Test 
240 HOURS  maximum  in 8 -12 Weeks      50  Modules = DIPLOMA
Total 720 HOURS  maximum  in 24 - 48 Weeks    168  Modules = DIPLOMA    
Occupational Classification Codes: 17-3028, 49-2093, 49-2094, 49-2095, 49-9012, 17-3028, 41-3099, 49-9046, 49-9069, 49-9081, 51-2021, 51-2022, 51-2023, 51-8013, 17-3028, 51-8031, 51-9162 

 

 


About CIT | Our Team | Contact Us

Tel: 562.925.1785

17156 BELLFLOWER BLVD
BELLFLOWER, CA 90706

At the College of Instrument Technology (CIT), we do not cut corners with your education and training. Your success reflects directly on our college, so we are in your corner from day one. CIT offers classes in many disciplines including CDL Commercial Truck Driving Level "A", Tow Truck Operator, Bus Driver Passenger Endorsement, numerous Heavy Equipment classes including Swing Cab Crane or Boom Truck Crane Certifications as well as Waste Water Management and various Instrument Calibration classes. Instrument Technology Process Control was Green before Green was cool. These certifications allow you to work anywhere in the world with these job skills. If you are over 18 years of age, have a clean criminal history, a good driving record, a desire to better yourself and your career, then you need to contact CIT as soon as possible.

GI Bill® is a registered trademark of the U.S. Department of Veterans Affairs (VA). More information about education benefits offered by VA is available at the official U.S. government Web site at http://www.benefits.va.gov/gibill

Copyright © 2015 College of Instrument Technology. All rights reserved.